DripWave Foil Type 1 corner

DripWave Foil

Flush horizontal and vertical joint design (no tongue & groove) for full-sheeted walls; suitable for commercial and residential use.

DripWave Foil Type 2 corner

DripWave Foil Connect

Tongue-and-groove horizontal joint design (flush vertical joints) for full-sheeted walls or bridging studs over open-faced walls; suitable for commercial and residential use.

DripWave Foil

Flush Horizontal & Vertical Joints (no tongue-and-groove horizontal joint design)

For full-sheeted walls; commercial and residential projects

Specifications

  • DripWave Foil board, compliant with ASTM C578
  • Nominal density of 1.0 lb/ft3
  • EPS board thickness: 1”, 1-¼”, 1-½”
    • Additional EPS board thicknesses available in ½-inch increments up to 4 inches
  • Minimum compressive strength of 10 psi
DripWave Foil Panel Sizes
  • 4’ x 8’ Expanded Polystyrene (EPS) insulations panels
  • 2’ x 8’ Expanded Polystyrene (EPS) insulations panels
  • 2’ x 4’ Expanded Polystyrene (EPS) insulations panels
R-Value Performance

The following stable R-values per inch, tested according to ASTM C518 or ASTM C177:

  • R5.45 at 25°F
  • R5.27 at 40°F
  • R4.95 at 75°F

System Components

The DripWave Foil insulation system is designed for residential and commercial full-sheeted walls and is an easy-to-install, cost-efficient, uncomplicated solution to complex exterior building wall issues.

DripWave Foil insulation is fully tested for resistance to water penetration, UV degradation, thermal resistivity and fire performance properties and complies with Type 1 of ASTM C578, “Standard Specification for Rigid Cellular Polystyrene Thermal Insulation.” Certified test results are available upon request.

The DripWave Foil insulation system has 4 major components:

  • Water-managed rigid foam board insulation with no tongue-and-groove joint design
  • Low “E” metalized radiant barrier
  • Self-adhering board joint tape
  • Galvanized metal weep screed

DripWave Foil Connect

Tongue-and-Groove Horizontal Joint Design

For full-sheeted walls or bridging studs on open-faced walls; residential or commercial

Specifications

  • DripWave Foil Connect board, compliant with ASTM C578
  • Nominal density of 1.5 lb/ft3
  • EPS board thickness: ⅞”, 1”, 1-½”
    • Additional EPS board thicknesses are available in 1/2 inch increments up to 4 inches
  • Minimum compressive strength of 15 psi
DripWave Foil Connect Panel Sizes
  • 4’ x 8’ Expanded Polystyrene (EPS) insulations panels
  • 2’ x 8’ Expanded Polystyrene (EPS) insulations panels
  • 2’ x 4’ Expanded Polystyrene (EPS) insulations panels
R-Value Performance

The following stable R-values per inch, tested according to ASTM C518 or ASTM C177:

  • R5.75 at 25°F
  • R5.56 at 40°F
  • R5.34 at 75°F

System Components

The DripWave Foil Connect insulation system is designed for residential and commercial projects for both sheeted walls and bridging studs on open-faced walls. When combined with a proper water-resistive barrier, wall sheathing panels and stucco finish system, Stytek’s DripWave system provides a cost-efficient, uncomplicated solution to complex exterior building wall issues.

DripWave Foil Connect insulation panels are fully tested for resistance to water penetration, UV degradation, thermal resistivity and fire performance properties and comply with Type II of ASTM C578, “Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation.” Certified test results are available upon request.

The DripWave Foil Connect insulation system has 4 major components:

  • Water-managed rigid foam board insulation with tongue-and-groove joint design
  • Low “E” metalized radiant barrier
  • Self-adhering board joint tape
  • Galvanized metal weep screed